mr6 KOJIRO 工事狼 土木・測量・工事・不動産

※ nothing charge if there is no will not be able to use only simple calculation and confirmation function

● operating environment

· Android 2.2 or more

● Menu not visible on the screen

- You appropriate menu appears each icon by press and hold

● coordinate list program

Insertion of one record and press the "X coordinate" button

Pressing the "Y coordinate" button when the removal of 1 record

● For startup

- Initial startup it will start in the sample data

- From the next startup it will start with the data that was last written to the terminal

● There is a case where data are currently working disappears Operating the task killer and memory release apps when you are allowed to "break" in HOMEkey

If the data is necessary to make the "end" of data without the "interruption" by HOMEkey it is written to the terminal

● presence of TS command can not connect with equipment compatibility problems and non-compliant when it is connected to the TS, because there is, be sure the connection confirmation of the TS using the pre-JobPoint

Since With regard to the pairing of Bluetooth devices is irrelevant to the application, inquiries should be addressed to the respective manufacturers of the subject

● Other

Brief description in the app is I will Yes and to be seen

• The input of the angle as well as the general survey software 123.1234 (123 degrees 12 minutes 12 seconds), 359.5959 Enter in the form of (359 degrees 59 minutes 59 seconds) (decimal point at the end of zero can be omitted is)

● basic SYS. ●

-system-

Information

And conditions set

· Condition setting: Calculation

·user registration

- Coordinate data -

· Coordinate List

· Coordinate data → SIMA file

· Coordinate data → APA file

· Coordinate data → XYH file

Initialization of-coordinate data

· SIMA file → coordinate data

· APA file → coordinate data

· XYH file → coordinate data

- Job Notes -

Jobs notes display of

- Of job data recovery

Jobs notes → TEXT file

Jobs notes → JOB file

Job erasing of note

· JOB file → job Notes

· TEXT file viewer

- (Former) calculation Notes

- Calculate menu -

(1) coordinate list

(2) coordinate input: New point number

(3) coordinate editing

(4) ST calculation

(5) ST calculation: Continuous

(6) ST calculation: move

(7) 3 points: interior angle distance

(8) 3 points: interior angle distance: Continuous

(9) 3 points: interior angle distance: Move

(10) perpendicular foot

(11) perpendicular foot: Continuous

(12) coordinate method area calculation

(13) radiation traverse

(14) intersection: 4 points

(15) intersection: three points and one direction angle

(16) intersection: two points and two direction angle

(17) intersection: 2 yen

(18) intersection: circle and a straight line: 1 point

(19) intersection: circle and a straight line: 2 points

(20) offset: 1 point

(21) offset: 2 points

(22) Offset: tip

(23) straight: perpendicular calculation

(24) straight: inside and outside equinox

(25) straight: move parallel

(26) straight: N equal parts

(27) straight: midpoint

(28) parallel movement intersection: 1 point

(29) parallel movement intersection: 2 points

(30) parallel movement intersection: 3 points

(31) city block calculation

(32) city block calculation: Continuous

(33) the corner cut calculation: side length

(34) the corner cut calculation: Sumisetsu-cho

(35) the corner cut calculation: arc

(36) a circle passing through the three points

● calculation curve ●

(37) single curve: Elements IA · R

(38) single curve: Hijikata curve

(39) single curve: BC point: IP · EC

(40) single curve: EC point: IP · BC

(41) single curve: element calculations

(42) single curve: curve length-chord · M

(43) single curve: IP points

(44) single curve: center point

(45) single curve: perpendicular calculation

(46) single curve: inside and outside equinox

(47) single curve: both ends move

(48) single curve: N equal parts

(49) single curve: midpoint

(50) single curve: offset: 1 point

(51) single curve: offset: 2 points

(52) single curve: offset: EC points

(53) Clothoid: Element: AR → L

(54) Clothoid: Element: AL → R

(55) Clothoid: Element: RL → A

(56) clothoid: dividing point

(57) Clothoid: N equal parts

(58) Clothoid: Offset: 1 point

(59) Clothoid: Offset: 2 points

(60) Clothoid: Offset: KE point

● Stakeout and observation ●

(61) TS: measurement test

(62) TS: Installation: resection

(63) TS: Installation: opposite side observation

(64) TS: Installation: BM → altitude

and (65) 2D: measurement design calculation

and (66) 3D: measurement design calculation

(67) 2D: radiation traverse

(68) 3D: radiation traverse

(69) APA field book file creation

● Bluetooth transfer ●

· APA reception → APA file

· APA file → APA transmission

· SIMA reception → SIMA file

· SIMA file → SIMA transmission

· TEXT reception → TEXT file

· TEXT file → TEXT transmission

● ver.1.34.01

· ST calculation: move the ST calculation: Continuous, 3 points: Cabinet distance: move three points: Cabinet distance: I was fixed had become continuous, in

● ver.1.34.00

We added a mesh 2 in graphic display

Initial value: 50m, color: gray

• The graphic display of the pitch of the mesh mesh 2 was so as not to draw and to 0m

● ver.1.33.00

· GR screen was to be able to specify the color of all the items of the (condition)

● ver.1.32.90

· TS OnAIr (measurement) of the horizontal screen when I was made possible

You have to be able to connect the server to the terminal you can not connect with the client in · TS OnAir

Condition: Bluetooth: Server · Master

● ver.1.32.80

● Announcements: Notes

Please file create a coordinate data on the memory to the previous version up

Data is written at the end in previous versions will no longer be read

● revisions

· Delete coordinate ※ to publish because inquiry is large in the erroneous deletion careful

You get a dialog If you press the "Y coordinate" button After instructing the measurement point in the "coordinate list"

· Coordinate the insertion of

You get a dialog If you press the "X coordinate" button After instructing the measurement point in the "coordinate list"

When you insert the data in the initial state for graphic screen is disturbed, and then insert the coordinates of the same data in a different point number

Measuring point name can be edited in the coordinate editing

And conditions: point name after calculation end the +1

And conditions: How when the point name to +1

- Revival of XYH file operation

File name that has changed the format for sharing with other apps will be * .xyht

It can not be read previous * .xyh

● ver.1.32.70

· TS you have changed the measurement screen

• The TS confirmation tone after the measurement was to be able to select it (conditions)

· TS we've changed the way of cutting the (Bluetooth)

Connection (automatic) is the same as ever, but it was changed to arbitrarily perform method cutting

It will cut with "TS button" long press menu of "cutting the TS (Bluetooth)"

The message of the case "was cut" is not a connection state does not appear

 It should be noted that, in the case of "termination of the application" at the connected state, it will be automatically disconnected

Please re-processed from the "cut" if by physical or other party software to connect with the other side Bluetooth was off